模具常用术语中英文对照表模板类加工类零件上托板钢板弹簧舌片备料板/镶件/嵌件备用板/模具镶块上垫脚顶块/平行板上夹入块冲头座镶块上盖板盖片上脱入块上部脱模镶块上模座冲头组/冲模组/冲模座下模入块艾德上背板冲压垫板冲孔冲头/冲头穿孔冲头/穿孔上垫板穿孔垫下料冲头切割模上夹板冲头把切边冲头/切舌冲头修边冲头/喷枪冲头止挡板止动板废料切边碎边剪上脱料板上部剥离器异形冲头特殊形状冲头下脱料板下部剥离器折弯冲头艾德内外脱料板脱模板内脱模板成形冲头/整形冲头成形冲头/冲头再冲击外脱料板外部剥离器拉伸冲头/抽芽冲拉伸冲头/挤压冲头内脱料板内部剥离器压毛边冲头去毛刺冲头上模板上板压线/压线冲头刻痕/凹槽冲头下模板下盘字印冲头冲压冲头凸模内螺模加强筋冲子变硬？肋骨？打卡？毒刺凹模阴模压平冲子/扩展冲冲压/扩张冲压拉伸凸模牵引环顶料销起模杆凹凸模特征模具导料板/导料块导向板/导向垫下垫板顶料板定位块压板定位块/定位板/压板下背板模具垫板挡块/拼块/压块挡板块/部分/锁块下夹板凹模固定板浮块/架模靠块升降块/合模块
下模座 | die set | | 垫板/垫块/垫片 | shim plate/padding block/ backup plate | | 下垫脚 | bottom block | | 滑块/滑板 | sliding block/slide plate |
| 料架 | stock support | | 滑块/滑板 | cam slide |
| 下托板 | bottom subplate | | 滑座 | sliding dowel block |
| 上模 | upper die base | | 滑道（槽） | sliding slot |
| 下模 | lower die | | 斜楔，楔块/锥度/斜锥 | （cam）driver/taper/angle pin |
| 压料板 | pressure plate | | 铜公 | copper electrode |
| 承料板 | stock supporting plate | | 刮料板 | stripper plate |
| 耐磨板 | wear plate | | 压块 | holder block |
| 支承板 | backing plate | | 码模槽/自动夹模器 | clamping slot/mounting/Automatic Clamper |
| 靠块 | block heel | | 自润滑板 | oir-free skateboard |
| 滴油块 | block oiler | | 初始挡料销 | trigger？Stop |
| 限位块 | block stop | | 优力胶 | PU(polyurethane） |
| 整形块 | restrike block/die restrike | | 插块 | block thrust |
| 开关座 | switch block | | 储运块 | block tie |
| 定制零件类 | | 模板加工有关名词 | | |
| 合销 | dowel pin | | 攻/穿/加工/间隙 | tap/through/machining/gap |
| 导引销（定位销） | guide pin/pilot pin/定位locator | | 钳工/机工/线割 | machine/tool marker/wire cut |
| 斜顶销/防粘销 | lifter pin/ejector | | 车/磨/铣/割/铰 | lathe/grind/mill/wire cut/ream |
| 气销 | lifter pin with AIR HOLE | | 磨掉/研磨 | grind off/tripsis |
| 浮升导料销 | lifter guide pin | | 钻/钻穿 | drill/drill through |
| 翻边圆入块 | extrude button | | 垫脚 | parallel |
| 成形入块 | form insert | | 冲孔冲头 | piercer |
| 导正 | guide | | 导引冲 | pilot |
| 导柱 | guide pin/pillar | | 微动开关 | Prox.Switch |
| 落料冲头 | blanking punch | | 耐磨入块 | wear insert |
| 传送杆 | transfer bar | | 耐磨滑块 | wear cam |
| 传送手指 | transfer finger | | 吹出 | blow off |
| 滑块导轨 | cam guide | | 圆入子 | button |
| 滑块入块 | cam insert | | 落料模 | blank die |
| 出料滑道 | chute | | 拍披锋模 | coin die |
| 圆入子套 | collar | | 模具侧视图 | die section |
| 初始挡料销 | finger stop pin | | 打色拉 | counter sink（down&up） |
| 氮气弹簧 | gas spring | | 放电机/放电 | EDM=Electron Discharge Machining/Discharge |
| 弹簧套 | spring box/cage | | 雕刻/文字 | Carving/Character |
| 弹簧 | coil spring | | 深/宽/高/长度 | depth/width/height/length |
| 弹簧柱 | spring rod | | 侧/单/斜/背 | profile/single/incline/back |
| 模柄/铆钉/铆合 | die shank/stacking/riveting punch | | 天部/底部 | top side/bottom side |
| 止高杆 | stopper rod | | 正面/反面 | nearsied/farside |
| 限位柱 | limited post | | 边缘/周边 | edge/round edge |
| 复位柱 | ejector plate returm pin | | 沉头孔/通孔 | counter bore/through-hole |
| 顶出销/打杆 | knowout pin/tip perch(ejector rob) | | 盲孔/抽孔 | rao |
| 导柱/导套 | guide pillars/guide bushes | | 倒角/不倒角 | chamfer/no chamfering |
| 内导柱/外导柱 | inner guiding post/outer guiding post | | 废料孔/落料孔 | slug hole/Fall materical's hole |
| 内导套/外导套 | inner bush/outer bush | | 气孔（排气槽） | gas vent |
| 脱料钉/脱料螺栓 | killer pin/stripper bolt | | 线孔/穿线孔/基准孔 | wire hole/thread hole/base hole |
| Hyson氮气组 | Hyson unit | | 叠片 | lamina |
| 入块 | insert | | 氮气弹簧板 | Manifold |
| 顶出杆/顶出 | knockout bar/knockout | | 微动开关 | Microswitch |
| 顶出弹簧 | knockout spring | | 油壶 | oiler |
| 等高套筒 | eq-height sleeves=spool/CSR | | 拉伸压料板 | pressure plate of draw |
| 等高螺丝 | stripper bolt | | 剖面线（阴影）阴影边 | hatching/shadow side |
| 公制/英制螺丝 | M-screw/E-screw | | 点划线/双线边 | chain doted line/crewel side |
| 内六角螺丝 | socket head cap screws | | | |
| 止付螺丝 | stop screw /set-scr | | 虚线 | dashed-line |
| 误送检知器 | misfeeder | | 轮廓（外形） | contour/shape/outline |
| 吊模螺丝 | Lifting screw/handle eye bolts | | 调制处理 | thermal refining |
| 吊模螺丝 | eye bolt/lifting eye bolts/hook | | 深冷处理/热处理 | subzero/heat treatment |
| 球形紧固块 | ball lock block | | 剪断/半剪 | shearing/semi-shearing |
| 球形紧顶料凸模 | ball lock male die | | 淬火 | quench hardening |
| 顶出 | knockout | | 正常化 | normalizing |
| 两用销/安全销 | guide lifter pin/check-pin | | 刀口 | edge/tool point/blade |
| 浮料块 | lifer | | 废料盒 | scrap retainer |
| 成形压板 | pad form | | 弹簧杆 | spring retainer |
| 顶料围板 | pad keeper | | 内限位柱 | stand off |
| 回程销 | return pin | | 皮带 | strap |
| 垫板 | riser | | 开关臂 | switch arm |
| 废料滑槽 | scrap chute | | 料架 | stock support |
| 衬套 | bush | | 准确性、精度/间隙 | accuracy/gap |
| 油槽/支架 | oil groove/ejector housing | | 挂台/让位/移位 | hang/Avoidance/shift |
| 连接杆/滚珠 | ejector tie rod/ball | | 键槽 | key groove/key slot |
| 抛光 | buffing/polish | | 逃料倾斜角 | draght angle |
| 上模螺丝 | upper screw | | 废料切断刀 | scrap cutter |
| 下模螺丝 | lower screw | | 交点/尖角/系数 | intersection/sharp corner/factor |
| 末端检置器 | bottom detector/inspect device at end | | 感应座/感应器 | mounting blocks for support legs |
| 终检/检查板 | final inspection/inspection plate | | 感应横梁 | bridge sensor/bar |
| 检测/安全检知 | detection/safety check utensil | | 感应支架 | bridge type support leg |
| 检测板 | feed sensor holder | | 感应后板 | protective cover for sensor |
| 料条加工类 | | 料条类 | | |
| 冲孔加工 | punching(piercing) | | 模具闭合高度 | die shut height |
| 切边加工 | trimming | | 送料高度/送料方向 | feeding height(pass line)feed direction |
| 冲缺口 | notching | | 材质/吨数/步距 | material/tonnage/pitch |
| 冲切缝 | lancing | | 模具结构图 | die structure dwg |
| 下料加工 | blanking | | 冲压力 | press pressure |
| 侧向冲孔 | cam piercing | | 客户品番 | Customer part NO. |
| 侧向切边 | side cut/side trim | | 客户 | customer |
| 折弯/拉伸 | bending/drawing | | 工程图/剖面图 | procedure dwg/Cross-section draw |
| 冲切/半切 | cutting/half cut/semi-trim | | 展开图 | extension dwg/expanding drawing |
| 空站/空步&拉伸 | idle&to pull,to stretch/draw | | 装配图 | essembly dwg |
| 切断出件 | cutoff/blanking/Part out | | 料带图/工序图 | strip layout/design blueprint/precess drawing |
| 整形/成形/整平 | restriking/forming/flatting | | 冲床规格 | press specification |
| 抽芽/翻边 | extrude(hole flanging)flange | | 修模/客户设变 | to repair a die/design/fix die/design change |
| 凸点/打凸苞 | emboss/emboss | | 新模 | |
| 打凸筋 | ribbing | | 接刀图 | cutter connecting drawing/mismatch drawing |
| 压毛边/面压 | deberr or coin | | 试模 | engineering mold testing/try-out die |
| 冲压铆合 | punch riveting | | 买，购买 | purchase,buy |
| 压线/向下压线 | groove(score)/bend line mark/grooving down | | 标准件 | standard parts |
| 向下打色拉 | Hourglass / CSK | | 铭牌 | name plate |
| 冲字印/字印 | stamp letter | | 备件 | spare parts |
| 字印 | stamp | | | |
| 压印 | coining | | 机工 | tool marker |
| 压花 | embossing | | 钳工 | machine |
| 卷圆 | Curl up | | 线割 | wire cut |
| 翻孔 | flanging hole | | 加工说明 | process notes |
| 凸状，凸面 | convexity | | 管制 | to control |
| 挫毛刺 | to file burr | | 试模 | engineering mold testing/try out die |
| 摆水平 | Rotate for Flat | | 中间开油槽 | open oil slot in the middle |
| 落料 | cut off/blank | | 用优力胶加工 | using polyurethane to machine |
| 摆斜45° | Rotate 45° | | 刀口直身 | lenth of straight area on blade |
| 第二次拉伸 | 2nd drawing | | 阴影部分天面磨压筋线 | grind rib on surface of hatching ar |
| 压线/面压 | scoie/Coin | | 顺送模/单发模/复合模 | progressive die/Single&Compound die |
| 向下成形 | form dowm | | 比例 | scale |
| 向上成形 | form up | | 码模槽 | mounting slots/clamping slots |
| 向下折弯/预折 | bend up/Pre-bending | | 外形 | Shape/outline |
| 向下折弯 | bend down | | 放大图 | Enlarge picture |
| 此段毛刺反向 | burr direction here is conversely | | 第一工程/工站 | first station |
| 接刀8处 | 8 PLACE FOR PIERCING INSERT CONNECTION | | A此段毛刺反向 | A burr direction here is conversary |
海量学习资料加奉先老师487209997
